0333 3210 692 0800 954 9570
 

Wed, 10/18/2017 - 09:09 -- sdukbewiser

Tyre pressures and tread depths: your safety check guide

Wed, 18/10/2017
Share Article
Tyre pressures and tread depths: your safety check guide

Checking your car tyre pressures and tread wear is important if you want to stay safe on the roads and potentially save money.

Chris Rosamond, Autoexpress news, reports

Tyres are one of those things motorists often take for granted – that is, until something goes wrong.  The majority of the time, tyres only attract drivers’ attention when it is coming up to MoT time, as there is a minimum legal requirement for tread depth. Aside from that, most tyres will only be given the time of day when they are flat or obviously damaged, but as a good driver you should be paying a little more attention to these vital bands of rubber. Your tyre pressures, tread depth and general condition should be checked on a regular basis.

One reason why checking your tyres is a sensible thing to do is that neglected tyres cost money. If tyre pressures aren’t kept to the correct levels, it not only increases fuel consumption, but also increases wear on various components. The reason being, a flat or underinflated tyre has more resistance to rotating due to the higher surface area of rubber being in contact with the road. This explains why cars with flat tyres pull to one side.

Also, bashing your tyres on the kerb regularly puts stress on the side walls and can increase the likelihood of malfunction. The condition of your tyres is possibly the most important aspect of vehicle safety, while fuel economy and your car's handling will also be affected by damaged or worn tyres. A puncture is one issue to deal with, but tyres can lose air pressure over time, so you should regularly check that all four tyres on your car are inflated to the correct pressure.

The correct tyre pressures for your car will be in your car's handbook (possibly spelt 'tires' if you happen to have a handbook from across the pond), and it will probably say to check them on a weekly basis. However, this isn't strictly necessary, although no expert would advise leaving tyres unchecked for more than a month.

As tyres are the only point of contact between your car and the road, tyre condition is arguably one of the most important aspects of vehicle safety.  A puncture can have immediate and devastating effects, but tyres can also suffer from an aptly named ‘slow puncture’, on top of naturally decreasing in pressure over time. It is because of the last two, that it is very important to regularly check your tyre pressures.

Legislation has made it easier to check tyre pressures, because since 2014, all new cars sold in the EU must come with a tyre-pressure monitoring system (TPMS). This systems use sensors within the car's wheels that can detect a drop in air pressure. This will then flash up a warning on the car's dashboard if it falls below a certain level, usually telling you which corner is affected. If you’ve bought a new car in the last year or two, then it’s likely to come fitted with TPMS.

If your car doesn’t have TPMS, you can retrofit it with aftermarket kits, and anyway it's easy to check your pressures using a manual or digital tyre pressure gauge. You can use the equipment provided on garage forecourts, although there’s often a small charge, and the system may not be the most accurate. Either way, the procedure for checking your pressures is the same.

How to check your car tyre pressures

Tyre pressure is measured using two units: bar (where 1 bar is the pressure of the Earth’s atmosphere at sea level) and pounds per square inch (shortened to psi). Most gauges will display both units, and so will your car’s handbook, which lists the recommended pressures. Most cars also have a sticker or plate on the inside of one of the doorframes or on the fuel filler flap with a table of pressures.

To check your pressures, you need to find each wheel’s tyre air valve, which is a small tube that sticks out of the wheel rim. Each one should have a little plastic screw-on cap dust cover, which you can easily unscrew by hand. Make sure you place it somewhere safe and don’t forget to screw it back on tightly when you’re finished.

Once the dust cap is off, you can place your pressure gauge over the valve, push it in slightly and hold it for a few seconds. A pressure reading should appear on the gauge’s dial or screen.

If any of your tyres aren’t at the correct pressure, the machines on garage forecourts can be programmed to pump them up – you simply input the correct pressure and it does the rest. If you’re at home, you can use a powered or foot-operated air pump to add air to the tyre, then check the pressure again to verify you’ve put enough in.

How to check tyre tread depth and condition

While you’re checking your tyre pressures, you should give them a visual inspection as well. Look for any nails or other sharp objects that may have become stuck in the tread, and watch out for any odd-shaped bulges in the tread surface or sidewall of the tyre.

If you do spot anything, head to a tyre centre or garage straight away, as damaged tyres like this can blow out without warning, potentially causing you to lose control of your car.

You should also pay close attention to your tyre tread depth. The law requires a minimum tread depth of 1.6mm in a continuous band around the central three quarters of the tyre. You can check the tyre’s tread depth with a tyre tread depth gauge, but for a quick visual check, manufacturers often mould little bars into the tread at a height of 1.6mm.

When the main tread blocks wear down to the height of the little bars, it’s time for a new tyre. Of course, we would always recommend changing your tyres well before they reach the legal minimum tread depth.

Knowing the legal limits and how weather and road conditions can affect your tyres is an important part of owning your own car. Staying on top of car maintenance is also a much safer and cost-effective way to keep your car in its best condition.

Get a Quote

News Categories

News Archive